عيوب السلامة في freightliner coe 1986
تعتمد نتائج البحث هذه على استعلام YMM وتحتوي على معلومات الاستدعاء العامة مثل التاريخ والرقم والمكونات والوصف واتصالات الشركة المصنعة ومعلومات الاتصال الخاصة بالإصلاح. إذا كنت بحاجة إلى معلومات أكثر تفصيلاً حول سيارتك، يمكنك طلب تقرير المركبة.
freightliner coe 1986
ملخص
THE STEERING GEAR MOUNTING BRACKET WELDS MAY CRACK UNDER CERTAIN STEERING LOAD CONDITIONS.
نتيجة
-
إصلاح
REPLACE STEERING GEAR MOUNTING BRACKET WITH A REDESIGNED BRACKET.
ملاحظات
SYSTEM:STEERING GEAR MOUNTING BRACKET.VEHICLE DESCRIPTION:HEAVY DUTY TRUCKS.
ملخص
CORROSION OF THE GRABHANDLE AT ITS MOUNTING SURFACE MAY LEAD TO CRACKING OR LOSS OF STRENGTH.
نتيجة
-
إصلاح
REPLACE GRABHANDLE AND ITS FASTENER WITH IMPROVED GRABHANDLE; ALSO, INSTALL GASKET BETWEEN THE HANDLE AND AIR STARTER RESERVOIR.
ملاحظات
SYSTEM:GRABHANDLE.VEHICLE DESCRIPTION:HIGH CAB OVER ENGINE TRUCK TRACTORS WITH GRABHANDLEATTACHED TO A VERTICAL AIR STARTER RESERVOIR.
ملخص
STEERING ARM MAY FAIL IF USED ON EATON EFA12F4 FROM AXLE IN CONJUNCTION WITH ROSS HFB70 POWER STEERING GEAR.
نتيجة
-
إصلاح
INSTALL A NONADJUSTABLE 1500 PSI POWER STEERING PUMP PRESSURE RELIEF VALVE TO LIMIT STEERING ARM FORCES. REPLACE STEERING ARM WITH A DESIGN CAPABLE OF WITHSTANDING HIGHER FORCES. ADJUST MAXIMUM POPPET VALVE SETTINGS TO 500 PSI AND ADJUST AXLE STOPS.
ملاحظات
SYSTEM: STEERING.VEHICLE DESCRIPTION: LONG CONVENTIONAL AND HCOE TRUCKS EQUIPPED WITH EATONEFA12F4 FRONT AXLE AND ROSS HFB70 STEERING GEAR.
ملخص
BUCKLING OF THE TILT CYLINDERS MAY OCCUR WHILE LOWERING THE VEHICLES CAB DUE TO IMPROPER USE OF THE CAB TILT SYSTEM.
نتيجة
-
إصلاح
REPLACE THE 1 1/2 IN. DIAMETER TILT CYLINDERS ON ALL 104 IN. CABS WITH 2 IN. DIAMETER CYLINDERS.
ملاحظات
SYSTEM: CAB TILT.VEHICLE DESCRIPTION: 104 IN. CAB OVER ENGINE TRUCKS.
ملخص
THE HANDHOLD MOUNTING SYSTEM, WHICH CONSISTS OF A TUBULAR HANDLE HELD IN THREE PLACES BY CAST ALUMINUM BRACKETS AND ATTACHED TO THE ENGINE EXHAUST MUFFLER HEAT SHIELD. VIBRATION FROM THIS SYSTEM CAUSES THE HANDHOLD PARTS TO WEAR. CONSEQUENCE OF DEFECT: IF THE PARTS WEAR THIN THE POSSIBILITY EXISTS THAT THE HANDHOLD MIGHT GIVE WAY UNDER THE WEIGHT OF A DRIVER. THIS COULD RESULT IN PERSONAL INJURY.
نتيجة
-
إصلاح
REPLACE THE END BRACKETS WITH A MODIFIED DESIGN UTILIZING A RUBBER ISOLATER. ALSO, ADD A PLASTIC SLEEVE TO THE CENTER BRACKET FOR ISOLATION.
ملاحظات
SYSTEM: STRUCTURE/HANDHOLD. VEHICLE DESCRIPTION: HIGH COE AND LONG CONVENTIAL TRACTORS EQUIPPED WITHVERTICAL BAR HANDHOLD.